Tweet
1983 truck 302 with 1988 lincoin mark 7 heads ran good made 168whp and 278ftlb. in my mustang burned oil, lots of oil. compleate heads to pan. priced to sell $1usd
1981 mustang 255 mostly compleate valve covers down. no front cover, oil pan or pickup. $1usd
1998 3.8l gm. compleate valve covers to pan lower intake is off. upper intake is junk no coils or o2 sensors. 128k $1
mid length headers for fox body mustang 3inch collectors. $20
dynomax mufflers 2 1/4 rusty $1 tail pipes are also avalible free good shape.
1 big ford starter for 157 tooth flywheel worked fine. $1
1 big ford starter for 164 tooth flywheel remaned never used $1
1 remaned standared rotation water pump for ford truck has small shaft never used $1
1 new ford fuel pump for mustang out of box never used $20
1 wiend sbc dual plane intake good used condition. $sold
1 set mt high rise aluminum valve covers sbc $sold
1 set sbc push rods need to be cleaned. $free
1 set used chevy pistons and rods for 350 free.
rx7 5 sp. trans out of a 1987 glx. in good condition needs shifter bushing. $75
8.8 with t-lock and 3.27 gears compleate minus one drum. four lug axles. $sold
2-10 JL subs in sealed box. with cheap e bay amp. and remote bass control.$75
1 dyno tech drive shaft. weighs in at a hefty 5 pounds. was made for sn95 with t56 swap its about 1 inch shorter then a stock fox drive shaft. I havent decided if Im going to install a longer yoke or not. looking for $200 has some minor damage on yoke when the trans went out on the car it was in.
157 or maybe 164 tooth 28oz not sure how to tell the deference and Im not counting the teeth. sfi approved flex plate and engine spacer plate. not sure of make there is a picture of a tiger on it. $20
more to come as I pull it out.
1981 mustang 255 mostly compleate valve covers down. no front cover, oil pan or pickup. $1usd
1998 3.8l gm. compleate valve covers to pan lower intake is off. upper intake is junk no coils or o2 sensors. 128k $1
mid length headers for fox body mustang 3inch collectors. $20
dynomax mufflers 2 1/4 rusty $1 tail pipes are also avalible free good shape.
1 big ford starter for 157 tooth flywheel worked fine. $1
1 big ford starter for 164 tooth flywheel remaned never used $1
1 remaned standared rotation water pump for ford truck has small shaft never used $1
1 new ford fuel pump for mustang out of box never used $20
1 wiend sbc dual plane intake good used condition. $sold
1 set mt high rise aluminum valve covers sbc $sold
1 set sbc push rods need to be cleaned. $free
1 set used chevy pistons and rods for 350 free.
rx7 5 sp. trans out of a 1987 glx. in good condition needs shifter bushing. $75
8.8 with t-lock and 3.27 gears compleate minus one drum. four lug axles. $sold
2-10 JL subs in sealed box. with cheap e bay amp. and remote bass control.$75
1 dyno tech drive shaft. weighs in at a hefty 5 pounds. was made for sn95 with t56 swap its about 1 inch shorter then a stock fox drive shaft. I havent decided if Im going to install a longer yoke or not. looking for $200 has some minor damage on yoke when the trans went out on the car it was in.
157 or maybe 164 tooth 28oz not sure how to tell the deference and Im not counting the teeth. sfi approved flex plate and engine spacer plate. not sure of make there is a picture of a tiger on it. $20
more to come as I pull it out.
Comment