Parting my 83 out HCI 302, T-5, 8.8

[5.0stang85]

I'm keeping- the Prostars/tires, AN fuel lines on the engine, Air cleaner, Electric fan setup, and any other misc. things I can use on my other project-

I will update this after work around 630pm tonight- feel free to call dibs on anything- parts can be delivered to the cities, some will be cash + exchange (to keep the car a roller)

PM or post for things not listed

Roller minus engine trans $1,200- lots of nice parts on/in the car

Motor (carb to oil pan, and Summit LTH's- no flywheel/clutch/fuel lines)- $2,500 FIRM but maybe part out- have $5k into it and 1,100 miles runs great makes good power
Ford Racing aluminum flywheel and CFDF clutch 5,000 miles- no slipping at all $300 for both
T-5 trans recently rebuilt (not while I had it) shifts great- has 6T speedo gear (needed to run 4.10+ gears) and newer bearing retainer- no shifter $300
Poly motor/trans mounts- includes X member $75
stock motor mounts $20 delivered- FREE if you come get them or buy something else
8.8 w/4.30's rebuilt by budderigs -no brakes- $450 with out exchange or $300 with (I need a axle to keep it rolling)
83-86 fiberglass 4" cowl hood $250- includes hood pins
3" Dr Gas X pipe (3 bolt flange) $50
Manual steering setup $250 w/ exchange of PS system
Stock fuel tank with working sending unit $400 -working ACCURATE sending units are not easy to come by... and it only works in a factory carb 83-85 car

[work in progress]

Price on striped roller

[Silversixspeed]

Price on the 8.8? Judging by your sig, it has 4.30s?

[5.0stang85]

Price on the 8.8? Judging by your sig, it has 4.30s?

Yes Ford Racing 4.30s, rebuilt by Budderigs on here, trac lok is a little weak but works

Price depends if you have another one to trade? $400 with out? $275 with a rear axle I can bolt back in I'm keeping the brakes to the car FYI they work great and I'd like to keep it that way..

Mike are you talking like stripped- nothing in/on the shell, or void of engine/trans?

[five0@minot.com]

How much to ship the poly motor/trans/x-member mounts to nd 58785? Thanks.

Also, any rust at all on the body??

[2000 roush]

Price on interior

[5.0stang85]

How much to ship the poly motor/trans/x-member mounts to nd 58785? Thanks.

Also, any rust at all on the body??

yes there is a little rust- bottom of doors, hatch lip, hole in pass. floor about the size of a quarter ($.25 cents), worst is around the sunroof, $I'll do $90 shipped to Minot (they have 1,100 miles on them and look brand new)- USPS money order only at the moment due to Paypal difficulties PM me for my info

I currently have a deal worked out for the roller(sans engine, trans, drive shaft, exhaust, wheels/tires) to be picked up on the weekend of the March 10th so if that falls through for some reason I'll let everyone know..

[Silversixspeed]

Yes Ford Racing 4.30s, rebuilt by Budderigs on here, trac lok is a little weak but works

Price depends if you have another one to trade? $400 with out? $275 with a rear axle I can bolt back in I'm keeping the brakes to the car FYI they work great and I'd like to keep it that way..

You want $275 for trading an axle, without brakes, and a weak trac lok? I'll pass.

[5.0stang85]

You want $275 for trading an axle, without brakes, and a weak trac lok? I'll pass.

LOL cause the clutches are so hard and expensive when you have to pull the axles to remove the brakes... whatever less work for me anyway

I would think $275 + your stock 100k axle would be a great deal for a axle that was rebuilt and had $600 dumped into

[Silversixspeed]

LOL cause the clutches are so hard and expensive when you have to pull the axles to remove the brakes... whatever less work for me anyway

I would think $275 + your stock 100k axle would be a great deal for a axle that was rebuilt and had $600 dumped into

I do not have a stock, 100k axle. It's similar, if not better than yours (also has aftermarket axle shafts, and is in great shape). Just was considering a different gear ratio, and was weighing the cost of swapping a similar axle with different gears as opposed to just swapping gears in mine.

[T RILEY]

yea thats a bargain. I wish he had 2 axles.

[5.0stang85]

I do not have a stock, 100k axle. It's similar, if not better than yours (also has aftermarket axle shafts, and is in great shape). Just was considering a different gear ratio, and was weighing the cost of swapping a similar axle with different gears as opposed to just swapping gears in mine.

LOL you coulda kept your axles.. mine are just stock Ranger pieces

If a deal is not reached here this weekend for those interested in the car then talk to Workinprogress as he is high bidder on the roller and he said he has a rear end for it..

[5.0stang85]

yea thats a bargain. I wish he had 2 axles.

even if I did they wouldn't fit your car anyway..